Homepanda.in Logo

how to clean water inlet valve on washing machine

The water inlet valve on a washing machine controls the amount of water that enters the washer during a wash cycle.

The valve for the water inlet is positioned on the back of the washer, and it is connected to the washer by two water inlet hoses.

The water for the washing machine is carried in one hose to the tub, and the water is removed from the tub by another hose.

Mineral deposits from the water have a tendency to accumulate over time and cause the water entry valve to get blocked.

This can cause the valve to stick in the open position and allow too much water to enter the washer.

It can also cause the valve to stick in the closed position and not allow any water to enter the washer.

If your washing machine is not filling up with water, or if the water is not draining properly, you may need to clean the water inlet valve.

You can clean the valve with a brush and vinegar solution.

Steps for how to clean water inlet valve on washing machine

1. Remove the power cord from the washing machine’s connection to the wall outlet.

2. Stop the flow of water to the washing machine by turning off the water supply.

3. Remove the two hoses from the back of the washer.

4. Mix a solution of 1 cup vinegar and 1 cup water.

5. Use a brush to clean the mineral deposits from the water inlet valve.

6. Rinse the valve with clean water.

7. Reattach the hoses to the back of the washer. 8. Start the washing machine’s water supply by turning on its faucet.

What exactly is a water inlet valve, and what function does it serve on a washing machine?

The water inlet valve is a relatively unnoticeable component of your washing machine due to its size and location.

But are you sure you understand what it is used for? Is it crucial to ensure that it is in good operational condition?

The water inlet valve is an apparently simple piece of hardware that controls the flow of water into the tub of the washing machine.

The valve is attached to the door frame and has two hoses, one going to the water supply line and another that goes to the top of the washing machine tub.

The hose leading to the top of the tub is called the drain hose and it allows water to drain out of the tub when it’s being emptied, which is useful for all kinds of reasons.

How Can I Determine Whether or Not the Water Inlet Valve on My Washing Machine Is Faulty?

If you’re noticing that your clothes don’t get as clean in cold water as they used to, or if your water bill seems unusually high, it could be due to a faulty water inlet valve.

When your washing machine fills with water, it flows into the machine through the water inlet valve.

This valve is there to ensure that your washer doesn’t overflow or leak when it’s filling with water.

If you notice that your machine isn’t filling up with as much water as it should, then the water inlet valve might just be faulty.

If your washing machine is leaving water in the tub after it’s done filling, your water inlet valve may be faulty.
 
A faulty valve can cause a number of issues with your washing machine, including but not limited to:
 
  • Unbalanced loads (because the filling process isn’t working as it should)
  • Soaking clothes (because the water is leaking into the tub rather than going through the washer)
  • An ineffective spin cycle (because there’s no water left to drain from the machine)
  • A faulty motor (because your washing machine is trying to operate without receiving any water)

To determine whether or not your water inlet valve is faulty, follow these steps:

1. Check the water supply First, check to see if the water supply to your home is turned on.

If it is, then check to see if the water supply to your washing machine is turned on.

If the water supply to your washing machine is turned off, then the water inlet valve is probably not at fault.

2. Check the water inlet valve If the water supply to your washing machine is turned on, then the next step is to check the water inlet valve.

The water inlet valve is located behind the washing machine.

To check the water inlet valve, remove the screws that hold it in place and then remove the valve.

3. Inspect the water inlet valve Inspect the water inlet valve for any signs of damage.

If the valve is damaged, then it will need to be replaced.

4. Check the water inlet hose If the water inlet valve is not damaged, then the next step is to check the water inlet hose.

The water inlet hose is located between the water inlet valve and the washing machine.

To check the water inlet hose, remove the hose from the valve and then check for any leaks.

5. Replace the water inlet valve If the water inlet valve is damaged or the water inlet hose is leaking, then the water inlet valve will need to be replaced.

Conclusion

We hope you enjoyed this article on how to clean the water inlet valve on your washing machine!

If you have any questions, feel free to leave them below and we will get back to you as soon as possible.

Table Of Content